Note If you purchased a 1242G access point, this quick start guide refers occasionally to an 802.11a radio. However, your 1242G access point does not contain an 802.11a radio; it only contains an 802.11b or 802.11g radio. Please disregard the sections in your quick start guide that refer specifically to an 802.11a radio. You should review this table and the instructions for opening the top cover. The table contains important information that you need to know so that you can successfully configure your access point.
Status Description Blue Normal operating condition and at least one wireless client device is associated with the access point. Light green Normal operating condition, but no wireless client devices are associated with the access point. Amber or red Error condition.
When Chromecast is connected to the router, you can find the MAC address and IP address of Chromecast in router settings. You can reserve the IP for the MAC address. Another solution is to get the $15 power brick with Ethernet adapter.
Radio and IP Address Configuration The access point ships with its radio disabled and no assigned IP address or service set identifier (SSID). You must enable them when you configure the access point for the first time. The access point no longer is assigned an IP address.
It is configured to obtain an IP address by using a DHCP server. If your network does not use a DHCP server, you must connect to the access point console port and assign a static IP address (See the. Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Statement 1001 Overview This guide is designed to help you minimally configure a Cisco Aironet 1240AG Series Access Point by using its GUI through your web browser. The GUI is the primary configuration tool. Configuration can also be performed by using the command-line interface (CLI). For instructions on using the CLI, see the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points.
Document Performing an advanced configuration Cisco IOS Software Configuration Guide for Cisco Aironet Access Points Cisco Aironet Command Reference for Cisco Aironet Access Points and Bridges Mounting the access point Cisco Aironet 1240AG Series Access Point Hardware Installation Guide System requirements, important notes, limitations, and last-minute updates Release Notes for Cisco Aironet 1240AG Series Access Points for Cisco IOS Release 12.3(7)JA (or later) These documents are on Cisco.com at the following URL: Unpacking the Access Point Follow these steps to unpack the access point: 1. Open the shipping container and carefully remove the contents. Return all packing materials to the shipping container and save it. Ensure that all items listed in the Package Contents section are included in the shipment. Check each item for damage. If any item is damaged or missing, notify your authorized Cisco sales representative. Package Contents Each access point package contains the following items: • Cisco Aironet 1240AG Series Access Point • Cisco Aironet 1240AG Series Power Module (universal power module)—optional • Mounting hardware kit • One mounting plate – Cable security bracket – Two suspended ceiling T-rail clips (accommodates standard and recessed T-rails) – One security hasp – Four 6 x 32 x ½ in.
Pan head Phillips machine screws – One 8 x 18 x ¾ in. Pan head Phillips sheet metal screws – 2 #8 plastic wall anchors – One 10 x 24 nut (for ground stud on mounting bracket) – Four rubber foot pads – Two cable tie wraps • Quick Start Guide: Cisco Aironet 1240AG Series Access Point • Safety Warnings for Cisco Aironet 1240AG Series Access Points • Cisco product registration and Cisco documentation feedback cards The following illustrations show the access point with its external antennas connected.
2 5-GHz antenna connector (right/primary) Installation Summary Installing the access point involves these operations: • Mounting the access point • Connecting power • Obtaining and assigning an IP address • Configuring power • Configuring basic settings • Enabling the radio interfaces • Configuring security settings Mounting the Access Point Detailed mounting instructions are in the Cisco Aironet 1240AG Series Access Point Hardware Installation Guide. This document is available on Cisco.com at the following URL: Connecting Power The access point can be powered locally by using the AC power module or over Ethernet using power sourcing equipment (PSE). The following illustration shows the power options for the access point. Warning This product must be connected to a Power over Ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. Odbc in excel for mac. Statement 353 The access point power options: • Option 1—Switches with sufficient inline power: – An inline power capable switch, such as the Catalyst 3550 PWR XL, 3560-48PS, 3750-48PS, 4500 with 802.3af Power over Ethernet module, or the 6500 with 802.3af Power over Ethernet module – Other inline power switches supporting the IEEE 802.af inline power standard • Option 2—Switches without sufficient inline power can use the power injector: – Cisco Aironet Power Injector (AIR-PWRINJ3 or AIR-PWRINJ-FIB) • Option 3—Local power using a power module. Note Some older switches and patch panels might not provide enough power to operate the access point. At power on, if the access point is unable to determine that the power source can supply sufficient power, the access point automatically deactivates both radios to prevent an over-current condition.