Invest more energy with patients. Some more established gadgets are never again bolstered. 
System Requirements • Smash: 4GB, 8GB+ suggested • CPU: Intel Core 2 Duo 2.4 Ghz or speedier processor – Intel Core i3, i5 or i7 suggested • Free hard plate space: 16GB • Upheld Operating Systems: OS X Mavericks (10.9),OS X Yosemite (10.10) or OS X El Capitan (10.11) • An Internet association for programmed item enactment (a fast unknown process) and access to online help • Worked in receiver or a Nuance-affirmed mouthpiece. See support.nuance.com/similarity for more data.
The answer depends on whether the switch is a switch. That is to say, is the switch only switching and relaying traffic on to a different device for routing, or, is it doing the routing decisions itself via SVIs (switched virtual interfaces). Best statistical software for mac.
Stack Exchange network consists of 174 Q&A communities including Stack Overflow, the largest, most trusted online community for developers to learn, share their knowledge, and build their careers. Visit Stack Exchange.
On a layer 3 switch, the port can be found by using a few simple commands on the device. However on a layer 2 switch, you have to log into both the switch and whatever device is doing the routing to locate the port. In either case, the commands are the same, just run on two different boxes for the layer 2 switch. On a Layer 3 switch: • Log into the switch and issue the following command (where ipaddress is the ip address of the host you are trying to locate: show ip arp *ipaddress* • The output should look similar to below, and give you the mac-address of the device (I've highlighted the mac-address below in bold). LYKINS-1861#show ip arp 172.20.1.100 Protocol Address Age (min) Hardware Addr Type Interface Internet 172.20.1.100 0 **28cf.da1d.1b05** ARPA Vlan10 • Now issue one of the following commands (where mac-address is the hardware address from previous step). Depending on the Cisco platform, sometimes the command is listed in either form.
Show mac address-table address *mac-address* show mac-address-table address *mac-address* • The output should look similar to below, the port you are looking for should be listed as the Destination Port: LYKINS-1861#show mac-address-table address 28cf.da1d.1b05 Destination Address Address Type VLAN Destination Port ------------------- ------------ ---- -------------------- 28cf.da1d.1b05 Dynamic 10 **FastEthernet0/1/1** On a Layer 2 switch: • Find out what device is doing the routing for this switch (you may have to look at the network documentation). Sometimes it is a ', where the Layer 2 VLANs are being trunked up to the router for the Layer 3 decisions. • Log into the routing device, and issue the following command (where ipaddress is the ip address of the host you are trying to locate: show ip arp *ipaddress* • The output should look similar to below, and give you the mac-address of the device (listed below in bold).
LYKINS-1861#show ip arp 172.20.1.100 Protocol Address Age (min) Hardware Addr Type Interface Internet 172.20.1.100 0 **28cf.da1d.1b05** ARPA Vlan10 • Now log into the Layer 2 switch • On that device issue one of the following commands (where mac-address is the hardware address from previous step). Depending on the Cisco platform, sometimes the command is listed in either form. Show mac address-table address *mac-address* show mac-address-table address *mac-address* • The output should look similar to below, the port you are looking for should be listed as the Destination Port: LYKINS-1861#show mac-address-table address 28cf.da1d.1b05 Destination Address Address Type VLAN Destination Port ------------------- ------------ ---- -------------------- 28cf.da1d.1b05 Dynamic 10 **FastEthernet0/1/1**.
Firstly, you need to get the MAC address, so get into a machine on the same VLAN and look at its neighbour table - Windows is netsh int ipv4 show neigh, Linux: ip nei Cisco: show ip arp x.x.x.x. Once you have that. If this is a discovery job on a layer 2 switch, do show mac address-table i 0011.2233.4455 - replacing the mac address bytes as appropriate.
If on the other hand it's a router, use show ip arp i 0011.2233.4455 - again replacing the MAC as appropriate. Obviously when you were getting the MAC, if it turned out to be directly connected to that router, you're already done. Long-term however, I heartily recommend that you setup LLDP (failing that, CDP) to your hosts so that you can identify them from either side. Is an absolutely excellent LLDP daemon for Linux that also supports CDP, EDP, SONMP and FDP.